0001 <?xml version="1.0" ?>
0002 <endurox>
0003 <appconfig>
0004 <!-- ALL BELLOW ONES USES <sanity> periodical timer -->
0005 <!-- Sanity check time, sec -->
0006 <sanity>1</sanity>
0007 <!-- If process have been state changed to other than dead, exit or not running
0008 but PID of program does not exists in system, then send internel message, then
0009 program have been stopped.
0010 In Seconds.
0011 -->
0012 <checkpm>5</checkpm>
0013 <!-- <sanity> timer, end -->
0014
0015 <!-- ALL BELLOW ONES USES <respawn> periodical timer -->
0016 <!-- Do process reset after 1 sec -->
0017 <restart_min>1</restart_min>
0018 <!-- If restart fails, then boot after +5 sec of previous wait time -->
0019 <restart_step>10</restart_step>
0020 <!-- If still not started, then max boot time is a 30 sec. -->
0021 <restart_max>30</restart_max>
0022 <!-- <sanity> timer, end -->
0023
0024 <!-- Time after attach when program will start do sanity & respawn checks,
0025 starts counting after configuration load -->
0026 <restart_to_check>20</restart_to_check>
0027 <!-- Send full service table every 5 seconds -->
0028 <brrefresh>5</brrefresh>
0029 </appconfig>
0030 <defaults>
0031 <min>1</min>
0032 <max>1</max>
0033 <autokill>1</autokill>
0034 <!-- Do not need respawning! -->
0035 <respawn>1</respawn>
0036 <!-- The maximum time while process can hang in 'starting' state i.e.
0037 have not completed initialization, sec -->
0038 <start_max>20</start_max>
0039 <!--
0040 Ping server in every X seconds (minimum step is <sanity>).
0041 -->
0042 <pingtime>9</pingtime>
0043 <!--
0044 Max time in seconds in which server must respond.
0045 The granularity is sanity time.
0046 -->
0047 <ping_max>40</ping_max>
0048 <!--
0049 Max time to wait until process should exit on shutdown
0050 -->
0051 <end_max>30</end_max>
0052 <!-- Interval, in seconds, by which signal sequence -2, -15, -9, -9.... will be sent
0053 to process until it have been terminated. -->
0054 <killtime>20</killtime>
0055 </defaults>
0056 <servers>
0057 <server name="atmi.sv42">
0058 <min>1</min>
0059 <max>1</max>
0060 <srvid>10</srvid>
0061 <sysopt>-e ${TESTDIR}/atmisv-dom2.log -r</sysopt>
0062 </server>
0063 <server name="tpbridge">
0064 <max>1</max>
0065 <srvid>101</srvid>
0066 <sysopt>-e ${TESTDIR}/bridge-dom2.log -r</sysopt>
0067 <appopt>-n1 -r -i 0.0.0.0 -p 20003 -tP -z30 -P0</appopt>
0068 </server>
0069 <server name="tpbridge">
0070 <min>0</min>
0071 <max>1</max>
0072 <srvid>200</srvid>
0073 <sysopt>-e ${TESTDIR}/bridge-dom2.log -r</sysopt>
0074 <appopt>-n1 -r -i 0.0.0.0 -p 20003 -tP -z30 -P0 -f</appopt>
0075 </server>
0076 </servers>
0077 </endurox>
0078
0079