0001 <?xml version="1.0" ?>
0002 <endurox>
0003 <appconfig>
0004 <!-- ALL BELLOW ONES USES <sanity> periodical timer -->
0005 <!-- Sanity check time, sec -->
0006 <sanity>1</sanity>
0007 <!-- If process have been state changed to other than dead, exit or not running
0008 but PID of program does not exists in system, then send internel message, then
0009 program have been stopped.
0010 In Seconds.
0011 -->
0012 <checkpm>5</checkpm>
0013 <!-- <sanity> timer, end -->
0014 <!-- ALL BELLOW ONES USES <respawn> periodical timer -->
0015 <!-- Do process reset after 1 sec -->
0016 <restart_min>1</restart_min>
0017 <!-- If restart fails, then boot after +5 sec of previous wait time -->
0018 <restart_step>10</restart_step>
0019 <!-- If still not started, then max boot time is a 30 sec. -->
0020 <restart_max>30</restart_max>
0021 <!-- <sanity> timer, end -->
0022 <!-- Time after attach when program will start do sanity & respawn checks,
0023 starts counting after configuration load -->
0024 <restart_to_check>20</restart_to_check>
0025 <!-- Send full service table every 5 seconds -->
0026 <brrefresh>5</brrefresh>
0027 <!-- Reload DDR time (1x sanity loop) -->
0028 <ddrreload>1</ddrreload>
0029 </appconfig>
0030 <defaults>
0031 <min>1</min>
0032 <max>1</max>
0033 <autokill>1</autokill>
0034 <!-- Do not need respawning! -->
0035 <respawn>1</respawn>
0036 <!-- The maximum time while process can hang in 'starting' state i.e.
0037 have not completed initialisation, sec -->
0038 <start_max>20</start_max>
0039 <!--
0040 Ping server in every X sanity units
0041 -->
0042 <pingtime>9</pingtime>
0043 <!--
0044 Max number of sanity units in which server must respond.
0045 The granularity is sanity time.
0046 -->
0047 <ping_max>40</ping_max>
0048 <!--
0049 Max time to wait until process should exit on shutdown
0050 -->
0051 <end_max>30</end_max>
0052 <!-- Interval, in seconds, by which signal sequence -2, -15, -9, -9.... will be sent
0053 to process until it have been terminated. -->
0054 <killtime>20</killtime>
0055 </defaults>
0056 <servers>
0057
0058 <server name="atmi.sv84">
0059 <min>1</min>
0060 <max>1</max>
0061 <srvid>10</srvid>
0062 <envs><env name="NDRX_RTGRP">DOM1</env></envs>
0063 <sysopt>-G -e ${TESTDIR}/atmisv-dom1.log -r -sT2:TESTSV</sysopt>
0064 </server>
0065
0066 <server name="atmi.sv84">
0067 <min>1</min>
0068 <max>1</max>
0069 <srvid>320</srvid>
0070 <envs><env name="NDRX_RTGRP">DOM3</env></envs>
0071 <sysopt>-G -e ${TESTDIR}/atmisv-dom13.log -r</sysopt>
0072 </server>
0073
0074 <server name="atmi.sv84">
0075 <min>1</min>
0076 <max>1</max>
0077 <srvid>420</srvid>
0078 <envs><env name="NDRX_RTGRP">DOM4</env></envs>
0079 <!-- perform dynamc adv groupt tests.. -->
0080 <sysopt>-G -e ${TESTDIR}/atmisv-dom14.log -r -sDADV/DUNA:DYNADV -sT2:TESTSV</sysopt>
0081 </server>
0082
0083 <server name="tpbridge">
0084 <max>1</max>
0085 <srvid>101</srvid>
0086 <sysopt>-G -e ${TESTDIR}/tpbridge-dom1.log -r</sysopt>
0087 <appopt>-f -n2 -r -i 127.0.0.1 -p 20003 -tA -z30 -P0</appopt>
0088 </server>
0089
0090 </servers>
0091
0092 <services>
0093
0094 <!-- Check the defaults... -->
0095 <defaults routing="RT1" />
0096 <service svcnm="TESTSV" />
0097
0098 </services>
0099
0100 <routing>
0101 <route routing="RT1">
0102 <field>T_CARRAY_2_FLD</field>
0103 <ranges>
0104 'A'-'C':DOM1
0105 ,'D'-MAX:DOM4
0106 </ranges>
0107 <buftype>UBF</buftype>
0108 <fieldtype>CHAR</fieldtype>
0109 </route>
0110
0111 </routing>
0112 </endurox>
0113
